Darshan Safety Zone

Back to Insights

fire proximity suit in Rishikesh

Specify Fire Proximity Suit

eadmin maMarch 25, 20266 min read
Silver Signature Fire Proximity Suit ready on a kit-room rack
In this article

A fire proximity suit is the aluminized kit you specify when a Rishikesh rescue drill or furnace entry puts radiant heat on the whole body.

You may be writing the indent for a fire station kit room along the Ganga corridor, a hillside workshop furnace face, or an industrial emergency locker that still sees night drills after the tourist traffic fades. The suit does not change with the pin code. Match the duty, the layer model, and the way your site dons full proximity PPE.

Name the full-body heat job

Responder wearing silver Signature Fire Proximity Suit at a heat drill

You are the person who has to name the PPE on the requisition. An apron covers the chest. A coat covers more of the torso. A proximity suit is for the job where radiant heat hits the whole body and the method already calls for a full suit, not a single accessory.

Signature Fire Proximity Suit is a full aluminized proximity suit with a pure aluminium foil coated silver face. It is free size. It is sold per piece. It is not the aluminium coat, the back-open coat, or the aluminized apron.

Put it on the work this suit is listed for.

  • Fire and rescue proximity drills: close approach work where the kit room stocks a full suit.
  • Furnace and foundry radiant zones: entry or stand-by beside a hot face that needs full-body cover.
  • Glass and high-temperature process areas: short spells where radiant heat is on every side.
  • Industrial emergency lockers: sites that stock a proximity suit instead of coat-only coverage.

Walk the duty before you raise the indent. Outside a Rishikesh shed the air can feel mild. At a furnace door or a training prop, the radiant load does not follow the weather report. Write whether the job is a drill, a furnace stand-by, or a rescue method, and whether coat-only PPE would leave arms, legs, or back bare.

If the drawing already calls for Signature Aluminium Coat or Signature Aluminized Apron, stop. Those are different SKUs. Swapping a suit in for an apron, or an apron in for a suit, breaks the method.

On the indent, write the job in plain words, such as “furnace proximity stand-by, full suit”. That line stops the wrong garment leaving stores.

Pick the layer model for duty

Layered silver Signature Fire Proximity Suit fabric on a stores table

The habit on old indents is to write “aluminized fire suit” and leave the model blank. That habit misses this product. Signature Fire Proximity Suit is sold per piece (NOS) in four layer builds. Size is free size on every row. Colour is silver. Coating is pure aluminium foil coated. Working temperature on every model is 600 °C to 1000 °C.

Choose the layer count for the duty in front of you.

  • DSZAL.2LS — 2 Layer, about 6 kg
  • DSZAL.3LS — 3 Layer, about 8 kg
  • DSZAL.4LS — 4 Layer, about 9 kg
  • DSZAL.5LS — 5 Layer, about 10 kg

Layer count is the variant axis. The product is not customizable beyond those four builds. Do not invent a fifth size, a separate radiant-heat figure, or a certificate number that is not on the current model list. Approximate weight rises with layers; put that figure on the indent only as listed.

Ask the drill lead or furnace supervisor how long the wearer stands in the radiant zone and how close they stand. A short kit-room practice and a long furnace stand-by are not the same duty, even when both sit in the same Rishikesh industrial belt. Put the model number on the indent with the free-size note and the temperature window.

If your site PPE procedure already names a layer count, copy that model. Do not drop a layer to make the suit feel lighter.

Don foil face out and check fit

Responders helping don a Signature Fire Proximity Suit before a drill

The suit only helps if the foil face looks at the heat and the closures hold for the whole spell. Hand the wearer the model with the garment, not after they have already stepped to the furnace door or the training prop.

  • Step 1: Match the model tag to the indent before anyone puts the suit on.
  • Step 2: Don it over the base clothing your site PPE procedure already names. Keep the silver foil face outward toward the radiant source.
  • Step 3: Check free-size fit at the closures so the panel sits square. A twisted panel leaves a strip of clothing bare to the heat.
  • Step 4: Complete the ensemble the way your site method says. Head, hand, and foot protection are separate site PPE decisions; do not invent inclusions that are not on the product model list.
  • Step 5: After the first heat spell or drill, look again. A strap that slipped, a panel that folded, or a foil face turned inward means the next spell starts with a fix.

On a Rishikesh night drill the outside air may feel mild while the prop or furnace face is still hot. Do not treat the suit as optional because the yard is cool. Radiant heat at close range does not follow the tourist weather report.

If the foil face is inward, stop the job and reverse the suit before anyone steps back into the radiant zone.

Inspect before every drill

Officer inspecting seams on a Signature Fire Proximity Suit

Stores should not issue a suit that already failed the last drill. Make the check part of the hand-out, not a favour someone remembers after a scare at the furnace door.

  • Step 1: Lay the suit flat or hang it loosely. Look at the silver foil face under good light.
  • Step 2: Check seams, closures, and panel edges for tears, burn-through, or foil that has lifted from the base fabric.
  • Step 3: Retire the piece if the foil is delaminated, cracked along a hard fold, or burned through. Do not patch radiant PPE with tape from the tool crib.
  • Step 4: Store dry, hung or flat. Sharp folds crack the foil face and shorten the life of the next shift’s kit.

Keep spare suits with the model written on the locker or bin, not on a scrap of paper that will be lost. A hillside workshop outage and a night rescue drill should not start with a search through unmarked silver garments.

Train the drill lead and the stores hand on the same retire rule. One person who “knows the suit still looks fine” is how a damaged face returns to the radiant zone.

If the foil lifts when you flex a corner, do not issue that suit. Raise a replacement indent for the same model number.

Made in Ahmedabad, sent to site

Signature Fire Proximity Suits ready for dispatch in a warehouse

Signature Fire Proximity Suit is made by Darshan Safety Zone in Ahmedabad, under the Signature brand. The company has made fire safety and heat protection products since 2012, and its quality system is certified to ISO 9001:2015.

Orders can be dispatched across India, including to a site in Rishikesh, and freight is confirmed in the quotation. There is no counter in Rishikesh, and there is no same-day promise.

Discussion (0)

Join the conversation

Sign in to leave a comment for our applications team.

Sign in to comment
No comments yet. Be the first to ask a specification question.

What do buyers ask before specifying?

Common questions on materials, applications, and plant fit.

Is Signature Fire Proximity Suit the same as Signature Aluminium Coat or the aluminized apron?
No. The proximity suit is the full-suit SKU. The aluminium coat and the aluminized apron are separate products. Follow the name on the method before stores raises the indent.
What temperature and size should I write on the indent?
Every model is free size, silver, pure aluminium foil coated, with a working temperature of 600 °C to 1000 °C. Add the layer model DSZAL.2LS, DSZAL.3LS, DSZAL.4LS, or DSZAL.5LS for the duty.
Does the suit include hood, gloves, and boots as confirmed kit?
Those components are not listed on the current model rows. Complete the ensemble the way your site PPE procedure already says. Do not invent inclusions from an old brochure.
Does this suit carry EN 469 or a separate 1200 °C radiant figure?
No. Those claims are not on the current model list. Use the working temperature 600 °C to 1000 °C. Darshan Safety Zone is ISO 9001:2015 certified as a company.
Which way should the foil face sit?
Keep the silver foil face outward toward the radiant heat source. Wear the suit over the base clothing your site PPE procedure already names.
Do you keep stock in Rishikesh for same-day issue?
No. Manufacturing is in Ahmedabad. Signature products can be dispatched across India, and freight is confirmed in the quotation. There is no local warehouse promise.
Can I order a custom size between the layer models?
No. The product is not listed as customizable. Only the four layer builds are offered at free size.
Can someone visit the plant to help pick the layer model?
Darshan Safety Zone can visit a site to recommend a product for the job. Ask for that when you request a quotation, and have the radiant duty and the PPE method ready. The visit does not replace the model number on the order.

Ready to specify this for your plant?

Request a quote on welding protection, fire blankets, PPE, and high-temperature insulation — or browse the factory catalog.

Closely related products, categories, and guides to continue your specification journey.